summaryrefslogtreecommitdiff
path: root/arch/mips/pthread_arch.h
AgeCommit message (Collapse)AuthorFilesLines
2018-10-16make thread-pointer-loading asm non-volatileRich Felker1-2/+2
this will allow the compiler to cache and reuse the result, meaning we no longer have to take care not to load it more than once for the sake of archs where the load may be expensive. depends on commit 1c84c99913bf1cd47b866ed31e665848a0da84a2 for correctness, since otherwise the compiler could hoist loads during stage 3 of dynamic linking before the initial thread-pointer setup.
2018-06-02fix TLS layout of TLS variant I when there is a gap above TPSzabolcs Nagy1-0/+1
In TLS variant I the TLS is above TP (or above a fixed offset from TP) but on some targets there is a reserved gap above TP before TLS starts. This matters for the local-exec tls access model when the offsets of TLS variables from the TP are hard coded by the linker into the executable, so the libc must compute these offsets the same way as the linker. The tls offset of the main module has to be alignup(GAP_ABOVE_TP, main_tls_align). If there is no TLS in the main module then the gap can be ignored since musl does not use it and the tls access models of shared libraries are not affected. The previous setup only worked if (tls_align & -GAP_ABOVE_TP) == 0 (i.e. TLS did not require large alignment) because the gap was treated as a fixed offset from TP. Now the TP points at the end of the pthread struct (which is aligned) and there is a gap above it (which may also need alignment). The fix required changing TP_ADJ and __pthread_self on affected targets (aarch64, arm and sh) and in the tlsdesc asm the offset to access the dtv changed too.
2016-04-03add support for mips and mips64 r6 isaRich Felker1-5/+4
mips32r6 and mips64r6 are actually new isas at both the asm source and opcode levels (pre-r6 code cannot run on r6) and thus need to be treated as a new subarch. the following changes are made, some of which yield code generation improvements for non-r6 targets too: - add subarch logic in configure script and reloc.h files for dynamic linker name. - suppress use of .set mips2 asm directives (used to allow mips2 atomic instructions on baseline mips1 builds; the kernel has to emulate them on mips1) except when actually needed. they cause wrong instruction encodings on r6, and pessimize inlining on at least some compilers. - only hard-code sync instruction encoding on mips1. - use "ZC" constraint instead of "m" constraint for llsc memory operands on r6, where the ll/sc instructions no longer accept full 16-bit offsets. - only hard-code rdhwr instruction encoding with .word on targets (pre-r2) where it may need trap-and-emulate by the kernel. otherwise, just use the instruction mnemonic, and allow an arbitrary destination register to be used.
2015-11-02properly access mcontext_t program counter in cancellation handlerRich Felker1-1/+1
using the actual mcontext_t definition rather than an overlaid pointer array both improves correctness/readability and eliminates some ugly hacks for archs with 64-bit registers bit 32-bit program counter. also fix UB due to comparison of pointers not in a common array object.
2015-10-15add comment documenting hard-coded opcode for reading mips thread pointerRich Felker1-0/+1
2015-06-25fix local-dynamic model TLS on mips and powerpcRich Felker1-0/+2
the TLS ABI spec for mips, powerpc, and some other (presently unsupported) RISC archs has the return value of __tls_get_addr offset by +0x8000 and the result of DTPOFF relocations offset by -0x8000. I had previously assumed this part of the ABI was actually just an implementation detail, since the adjustments cancel out. however, when the local dynamic model is used for accessing TLS that's known to be in the same DSO, either of the following may happen: 1. the -0x8000 offset may already be applied to the argument structure passed to __tls_get_addr at ld time, without any opportunity for runtime relocations. 2. __tls_get_addr may be used with a zero offset argument to obtain a base address for the module's TLS, to which the caller then applies immediate offsets for individual objects accessed using the local dynamic model. since the immediate offsets have the -0x8000 adjustment applied to them, the base address they use needs to include the +0x8000 offset. it would be possible, but more complex, to store the pointers in the dtv[] array with the +0x8000 offset pre-applied, to avoid the runtime cost of adding 0x8000 on each call to __tls_get_addr. this change could be made later if measurements show that it would help.
2012-10-15add support for TLS variant I, presently needed for arm and mipsRich Felker1-4/+8
despite documentation that makes it sound a lot different, the only ABI-constraint difference between TLS variants II and I seems to be that variant II stores the initial TLS segment immediately below the thread pointer (i.e. the thread pointer points to the end of it) and variant I stores the initial TLS segment above the thread pointer, requiring the thread descriptor to be stored below. the actual value stored in the thread pointer register also tends to have per-arch random offsets applied to it for silly micro-optimization purposes. with these changes applied, TLS should be basically working on all supported archs except microblaze. I'm still working on getting the necessary information and a working toolchain that can build TLS binaries for microblaze, but in theory, static-linked programs with TLS and dynamic-linked programs where only the main executable uses TLS should already work on microblaze. alignment constraints have not yet been heavily tested, so it's possible that this code does not always align TLS segments correctly on archs that need TLS variant I.
2012-09-07add clang-compatible thread-pointer code for mipsRich Felker1-0/+4
clang does not presently support the "v" constraint we want to use to get the result from $3, and trying to use register...__asm__("$3") to do the same invokes serious compiler bugs. so for now, i'm working around the issue with an extra temp register and putting $3 in the clobber list instead of using it as output. when the bugs in clang are fixed, this issue should be revisited to generate smaller/faster code like what gcc gets.
2012-07-12mipsel (little endian) supportRich Felker1-1/+1
the fields in the mcontext_t are long long (for no good reason) even on 32-bit mips, so the offset of the instruction pointer (as a word) varies depending on endianness.
2012-07-11initial version of mips (o32) port, based on work by Richard Pennington (rdp)Rich Felker1-0/+8
basically, this version of the code was obtained by starting with rdp's work from his ellcc source tree, adapting it to musl's build system and coding style, auditing the bits headers for discrepencies with kernel definitions or glibc/LSB ABI or large file issues, fixing up incompatibility with the old binutils from aboriginal linux, and adding some new special cases to deal with the oddities of sigaction and pipe syscall interfaces on mips. at present, minimal test programs work, but some interfaces are broken or missing. threaded programs probably will not link.