| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
the adjustment made is entirely a function of TLS_ABOVE_TP and
TP_OFFSET. aside from avoiding repetition of the TP_OFFSET value and
arithmetic, this change makes pthread_arch.h independent of the
definition of struct __pthread from pthread_impl.h. this in turn will
allow inclusion of pthread_arch.h to be moved to the top of
pthread_impl.h so that it can influence the definition of the
structure.
previously, arch files were very inconsistent about the type used for
the thread pointer. this change unifies the new __get_tp interface to
always use uintptr_t, which is the most correct when performing
arithmetic that may involve addresses outside the actual pointed-to
object (due to TP_OFFSET).
|
|
the only part of TP_ADJ that was not uniquely determined by
TLS_ABOVE_TP was the 0x7000 adjustment used mainly on mips and powerpc
variants.
|
|
this will allow the compiler to cache and reuse the result, meaning we
no longer have to take care not to load it more than once for the sake
of archs where the load may be expensive.
depends on commit 1c84c99913bf1cd47b866ed31e665848a0da84a2 for
correctness, since otherwise the compiler could hoist loads during
stage 3 of dynamic linking before the initial thread-pointer setup.
|
|
In TLS variant I the TLS is above TP (or above a fixed offset from TP)
but on some targets there is a reserved gap above TP before TLS starts.
This matters for the local-exec tls access model when the offsets of
TLS variables from the TP are hard coded by the linker into the
executable, so the libc must compute these offsets the same way as the
linker. The tls offset of the main module has to be
alignup(GAP_ABOVE_TP, main_tls_align).
If there is no TLS in the main module then the gap can be ignored
since musl does not use it and the tls access models of shared
libraries are not affected.
The previous setup only worked if (tls_align & -GAP_ABOVE_TP) == 0
(i.e. TLS did not require large alignment) because the gap was
treated as a fixed offset from TP. Now the TP points at the end
of the pthread struct (which is aligned) and there is a gap above
it (which may also need alignment).
The fix required changing TP_ADJ and __pthread_self on affected
targets (aarch64, arm and sh) and in the tlsdesc asm the offset to
access the dtv changed too.
|
|
using the actual mcontext_t definition rather than an overlaid pointer
array both improves correctness/readability and eliminates some ugly
hacks for archs with 64-bit registers bit 32-bit program counter.
also fix UB due to comparison of pointers not in a common array
object.
|
|
other archs use asm for the thread pointer load, so making that asm
volatile is sufficient to inform the compiler that it has a "side
effect" (crashing or giving the wrong result if the thread pointer was
not yet initialized) that prevents reordering. however, powerpc and
or1k have dedicated general purpose registers for the thread pointer
and did not need to use any asm to access it; instead, "local register
variables with a specified register" were used. however, there is no
specification for ordering constraints on this type of usage, and
presumably use of the thread pointer could be reordered across its
initialization.
to impose an ordering, I have added empty volatile asm blocks that
produce the "local register variable with a specified register" as
an output constraint.
|
|
With the exception of a fenv implementation, the port is fully featured.
The port has been tested in or1ksim, the golden reference functional
simulator for OpenRISC 1000.
It passes all libc-test tests (except the math tests that
requires a fenv implementation).
The port assumes an or1k implementation that has support for
atomic instructions (l.lwa/l.swa).
Although it passes all the libc-test tests, the port is still
in an experimental state, and has yet experienced very little
'real-world' use.
|
